Connect this jack to the “IR IN” jack on Harman Kardon or other compatible equipment. J Remote IR Input: If the AVR 3000’s front-panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.
Before using the remote, it is important to remember to press the Device Control Selector button a b c that corresponds to the unit you wish to operate. In addition, the AVR 500’s remote is shipped from the factory to operate the AVR 500 and most Harman Kardon CD or DVD players and cassette decks.
If you get stuck in repairing a defective appliance download this repair information for help. See below. Good luck to the repair! Please do not offer the downloaded file for sell only use it for personal usage! Looking for other manual?
INTRODUCTION 3. Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon AVR 3000 you are about to begin many years of lis-tening enjoyment. The AVR 3000 has been cus-tom designed to provide all the excitement and detail of movie sound tracks and every nuance of musical selections.
If you have any question about repairing write your question to the Message board. For this no need registration.
Please take a look at the below related repair forum topics. May be help you to repair.
Warning! If you are not familiar with electronics, do not attempt to repair! You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived, so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them. These free programs can be found on this page: needed progs If you use opera you have to disable opera turbo function to download file! If you cannot download this file, try it with CHROME or FIREFOX browser.
Sziastok, Harman Kardon AVR 355 nem kapcsol be,sötét a kijelző led sem világít viszont halk kattanás-l meghúz egy relé tápok rendben,púpos kondik nincsenek. 'Az a helyzet az sajna mostanában nincs időm és lehetőségem a javításra ha lenne valaki aki Budapesti esetleg 13.ker és szomszédos kerületi és bevállalná a javítást persze nem ingyen írjon PÜ-t. Előre is köszi!'
Sziasztok! A fenti erősítő hibára szeretnék megoldást találni,hátha valaki találkozott ilyen hibával!Az erősítő hibásan került hozzám a fiam így vette,hátha meglehet javítani!Előttem már próbálták javítani látszik a táp panelon!A tápnál két ellenálást,egy diodát,és egy 5 voltos stab kellet cserélni,valamint a végfok egyik csatornáján a 2x27ohm 5w kellet cserélni! Azóta bekapcsol látszólag minden működik,de csak az analóg csatornák működnek,AUX,CD,6 channel input!A rádió és HDMI rész nem működik! A softver verziót sem írja ki rendesen,csak a dátumot(14-04-2008 09)Ezért arra gondolok sérült a Firmware! Az icknél még egyszer ellenőriztem a tápok megvannak! Ha valakinek lenne egy firmware mentése megpróbálnám beleírni hátha megoldaná a hibát! cserélve lett KIA278R05PI~ +5v vd 4.9volt 680mA,(legmelegebb ic 42fok ic75)
Sziasztok, Harman kardon soundsticks III került hozzám. Végfok hibával. A végfok TDA8561Q. Sajnos rajzom nincs hozzá. A problémám hogy nem tudom szólalásra bírni. A végfok IC-t kiforrasztvan a végfok IC 14 es láván 0V-ot mérek ami azt jelenti ha jól tudom, hogy készenléti állapotban van. A végfok csere után kimenetein nincs fesz a 14 es láb kivételével minden jónak tűnik. Ha berakom az IC/t akkor is ez a helyzet. Tápok rendben, az IC lábain mérem a bemenő jeleket ha adok rá. A 14 es láb feszültségét egy tranzisztor húzza le földre. A tranzisztor jó. Bázisán 0,66V. A panelen nem lehet látni mi mivel van összekötve csak pár alkatrészt. Ha valaki találkozott már ezzel a csodával, vagy van ötlete esetleg rajza azt megköszönném. Üdv.: Gy
Denon Avr 3000
Sziasztok! A fenti erősítőhöz keresnék szoftvert, akár lehet régebbi is. Ha valaki letöltötte és meg is őrizte esetleg.
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test or write your question to the Message board without registration. You can write in English language into the forum (not only in Hungarian)!